Tower Ladder

Approx. Rs 55,000 / PieceGet Latest Price

Product Details:

 

Main frame: This ladder is made up of aluminium alloy “C” section 66*32*3.18 mm thickness. HE30/ 6351 /T6 Grade. 

Steps: The steps are made up of non slip aluminium alloy corrugated fluted pipe step of 1” dia and 3 mm thickness HE30 / 6063/T6 Grade

·        Chemical composition (Si- 00.500, Fe- 0.140, Cu- 0.002, Mn-0.009, Mg-0.540, Cr-0.002, Zn-0.004, Ti-0.010, V-0.00, Zr-0.00) Aluminium – 98.74

·        Mechanical properties – UTS(Mpa)-182.22, % Elongation on 50mm GL- 14, 0.2% Proof stress Mpa – 173.53 (Certificate confirms to IS 733)

 

Step Interval: Every step has an interval of 12” for easy climbing and the ladder has a single sliding movement. Both sides of the flutted pipe steps are covered with plastics caps to avoid insects going in.

 

Platform size: We are providing a platform on top of the ladder(Platform size:17.5×19 inch) which is made up of aluminum alloy framed with aluminum “L” angle and  Chequered sheet of 3 mm thick

 

MS Trolley: The ladder base is made of MS Channels (100*50*6mm) and the  “L” angle (50*50*6mm). The MS trolley size is 5 feet x 6 feet on ground. The trolley is moved by means of tow bar.

 

Wheels: We are providing 4 Wheels Solid rubber tyre wheels with double ball bearing of Wheel size 14×4 inch, where 2 fixed wheel at the rear side and 2 round table arrangement at the front side.  This wheel can withstand one tone capacity..

 

Screw jack: We are  providing 4 Nos Screw Jack for ground resting to immobilizes the ladder when in use. The ladder cannot move if the jacks are screwed to the ground on 4 sides. .

 

MS Square Block: The ladder can be tilted from 0 to 90 degree by means of special MS Bracket made of square block (125*40mm).The overall tilting load is bared by MS bracket. We are also providing extra tie rod for stability of the ladder in extension position.

Wire rope: We are providing double wire rope for extension and single rope for tilting the ladder. The extension and tilting wire rope is 6 mm thick

 

 

 

 

 

 

 

Winch mechanism: We are specially providing 2 nos winch with double drum and double rope mechanism (Double drum for extension ) and (Single drum for tilting )the ladder  one winch is for tilting the ladder from 0 to 90 degree and the another winch is to extend the ladder to required height . Each winch is provided with Ratchet for safety in order to stop the winch reversing back unconditionally.

 

Load capacity: Over all load capacity of the ladder is 150 kg inclusive of user weight and hand tool

 

Important: Safe working – vertical only. Inclined working on ladders – NOT PERMITTED

 

Guarantee: Our ladders are guaranteed for 12 months from date of Invoice

Approx. Rs 45,000 / PieceGet Latest Price

Product Details:

BRIEF DESCRIPTION MODEL GKM 110  (Ht: 15-25 Ft, Ht:17-30 Ft & Ht:20-36 Ft) 

 

Main frame: This ladder is made up of aluminium alloy “C” section 66*32*3.18 mm thickness. HE30/ 6351 /T6 Grade.

·         Chemical composition (Si- 00.900, Fe- 0.160, Cu- 0.070, Mn-0.60, Mg-0.770, Cr-0.010, Zn-0.010, Ti-0.020, V-0.001, Zr-0.001) Aluminium – 97.50

·         Mechanical properties – UTS(Mpa)-353.14 , % Elongation on 50mm GL- 11, 0.2% Proof stress Mpa – 338.43 (Certificate confirms to IS 733-1983/64430-T6)

 

Steps: The steps are made up of non slip aluminium alloy corrugated fluted pipe step of 1” dia and 3 mm thickness HE30 / 6063/T6 Grade

·         Chemical composition (Si- 00.500, Fe- 0.140, Cu- 0.002, Mn-0.009, Mg-0.540, Cr-0.002, Zn-0.004, Ti-0.010, V-0.00, Zr-0.00) Aluminium – 98.74

·         Mechanical properties – UTS(Mpa)-182.22, % Elongation on 50mm GL- 14, 0.2% Proof stress Mpa – 173.53 (Certificate confirms to IS 733)

 

Step Interval: Every step has an interval of 12” for easy climbing and the ladder has a single sliding movement. Both sides of the flutted pipe steps are covered with plastics caps to avoid insects going in.

 

Platform size: We are providing a platform on top of the ladder(Platform size:17.5×19 inch) which is made up of aluminum alloy framed with aluminum “L” angle and  Chequered sheet of 3 mm thick

 

MS Trolley: The ladder base is made of MS Channels (100*50*6mm) and the  “L” angle (50*50*6mm). The MS trolley size is 5 feet x 6 feet on ground. The trolley is moved by means of tow bar.

 

Wheels: We are providing 4 Wheels Solid rubber tyre wheels with double ball bearing of Wheel size 14×4 inch, where 2 fixed wheel at the rear side and 2 round table arrangement at the front side.  This wheel can withstand one tone capacity..

 

Screw jack: We are  providing 4 Nos Screw Jack for ground resting to immobilizes the ladder when in use. The ladder cannot move if the jacks are screwed to the ground on 4 sides. .

 

MS Square Block: The ladder can be tilted from 0 to 90 degree by means of special MS Bracket made of square block (125*40mm).The overall tilting load is bared by MS bracket. We are also providing extra tie rod for stability of the ladder in extension position.

Wire rope: We are providing double wire rope for extension and single rope for tilting the ladder. The extension and tilting wire rope is 6 mm thick

 

 

 

 

 

 

 

Winch mechanism: We are specially providing 2 nos winch with double drum and double rope mechanism (Double drum for extension ) and (Single drum for tilting )the ladder  one winch is for tilting the ladder from 0 to 90 degree and the another winch is to extend the ladder to required height . Each winch is provided with Ratchet for safety in order to stop the winch reversing back unconditionally.

 

 

 

Approx. Rs 65,000 / PieceGet Latest Price

Product Details:

Requirement of Accessories: for 43 feet 1. H Frame         - 13 Nos.        Made out of Aluminium round plain pipe.        Grade : HE 30 – T6 temper Hindalco makeHeight            : 2000 mmWidth             : 1320 mmThickness         : 2 mm.Pipe  Dia         : 50mmNull Points       : 1 to 7 2. Cabin - 2 Nos. (Extra Additional Guard Rail Frame)        Height             : 1000mm        Width              : 1320 mm        Null Points        : 4 Nos. 3. Platform                 - 8 Nos. = (7 + 1)        Size : 580 x 1690 mm            Provide – ½” thickness Plywood for only working platform. 4. Stairway - 6 Nos.        Tube Size : 25 x 75 mm         Height    : 2500 mm        8 Steps   : Width : 3 inches 5. Hand rails        - 6 Nos.        Pipe Dia       : 50 mm        Length         : 2540 mm 6. Horizontal Bar    - 6 Nos.        Length    : 1700 mm        Thickness : 2 mm        Pipe  Dia : 50mm      Null Points : 2 Nos,  each 7. Hinged Stabilizer        - 4 Nos.Length : 4015 mm        Thickness : 2 mmPipe  Dia         : 50mmCentre Pipe       : 600 mm 8. “U” Clamp        - 30 Nos. : Made out G.I. 10. Wheels         - 4 Nos.   Size : 8” x 2” – Nylon wheels with foot brake systemand also leveling adjustment

Approx. Rs 37,500 / PieceGet Latest Price

Product Details:

 

Main frame: This ladder is made up of aluminium alloy “C” section 66*32*3.18 mm thickness. HE30/ 6351 /T6 Grade.

·       teps: The steps are made up of non slip aluminium alloy corrugated fluted pipe step of 1” dia and 3 mm thickness HE30 / 6063/T6 Grade

·        Chemical composition (Si- 00.500, Fe- 0.140, Cu- 0.002, Mn-0.009, Mg-0.540, Cr-0.002, Zn-0.004, Ti-0.010, V-0.00, Zr-0.00) Aluminium – 98.74

·        Mechanical properties – UTS(Mpa)-182.22, % Elongation on 50mm GL- 14, 0.2% Proof stress Mpa – 173.53 (Certificate confirms to IS 733)

 

Step Interval: Every step has an interval of 12” for easy climbing and the ladder has a single sliding movement. Both sides of the flutted pipe steps are covered with plastics caps to avoid insects going in.

 

Platform size: We are providing a platform on top of the ladder(Platform size:17.5×19 inch) which is made up of aluminum alloy framed with aluminum “L” angle and  Chequered sheet of 3 mm thick

 

MS Trolley: The ladder base is made of MS Channels (100*50*6mm) and the  “L” angle (50*50*6mm). The MS trolley size is 5 feet x 6 feet on ground. The trolley is moved by means of tow bar.

 

Wheels: We are providing 4 Wheels Solid rubber tyre wheels with double ball bearing of Wheel size 14×4 inch, where 2 fixed wheel at the rear side and 2 round table arrangement at the front side.  This wheel can withstand one tone capacity..

 

Screw jack: We are  providing 4 Nos Screw Jack for ground resting to immobilizes the ladder when in use. The ladder cannot move if the jacks are screwed to the ground on 4 sides. .

 

MS Square Block: The ladder can be tilted from 0 to 90 degree by means of special MS Bracket made of square block (125*40mm).The overall tilting load is bared by MS bracket. We are also providing extra tie rod for stability of the ladder in extension position.

Wire rope: We are providing double wire rope for extension and single rope for tilting the ladder. The extension and tilting wire rope is 6 mm thick

 

 

 

 

 

 

 

Winch mechanism: We are specially providing 2 nos winch with double drum and double rope mechanism (Double drum for extension ) and (Single drum for tilting )the ladder  one winch is for tilting the ladder from 0 to 90 degree and the another winch is to extend the ladder to required height . Each winch is provided with Ratchet for safety in order to stop the winch reversing back unconditionally.

 

Load capacity: Over all load capacity of the ladder is 150 kg inclusive of user weight and hand tool

 

Important: Safe working – vertical only. Inclined working on ladders – NOT PERMITTED

 

Guarantee: Our ladders are guaranteed for 12 months from date of Invoice