Trolley Tower Ladder

Approx. Rs 55,000 / UnitGet Latest Price

·        Chemical composition (Si- 00.500, Fe- 0.140, Cu- 0.002, Mn-0.009, Mg-0.540, Cr-0.002, Zn-0.004, Ti-0.010, V-0.00, Zr-0.00) Aluminium – 98.74

·        Mechanical properties – UTS(Mpa)-182.22, % Elongation on 50mm GL- 14, 0.2% Proof stress Mpa – 173.53 (Certificate confirms to IS 733)

Step Interval: Every step has an interval of 12” for easy climbing and the ladder has a single sliding movement. Both sides of the fluted pipe steps are covered with plastics caps to avoid insects going in.

Platform size: We are providing a platform on top of the ladder(Platform size:20.5×18 inch) which is made up of aluminum alloy framed with aluminum “L” angle and  Chequered sheet of 3 mm thick, provided with a floating type platform gauge 3 feet from the top and also provided with tool tray. The ladder can be used in variation degree from 90 degree up to 45 degree

MS Trolley: The ladder base is made of MS Channels (100*50*6mm) and the  “L” angle (50*50*6mm). The MS trolley size is 5 feet x 6 feet on ground. The trolley is moved by means of tow bar.

Counter weight: Counter weight will be provided at the bottom of the trolley in order to balance the ladder weight in variation degree.

Wheels: We are providing 4 Wheels Solid rubber tyre wheels with double ball bearing of Wheel size 14×4 inch, where 2 fixed wheel at the rear side and 2 round table arrangement at the front side.  This wheel can withstand one tone capacity..

Screw jack: We are providing 4 Nos Screw Jack for ground resting to immobilizes the ladder when in use. The ladder cannot move if the jacks are screwed to the ground on 4 sides.

MS Square Block: The ladder can be tilted from 0 to 90 degree by means of special MS Bracket made of square block (125*40mm).The overall tilting load is bared by MS bracket. We are also providing extra tie rod for stability of the ladder in extension position.

Wire rope: We are providing double wire rope for extension and single rope for tilting the ladder. The extension and tilting wire rope is 6 mm thick

Winch mechanism: We are specially providing 2 nos winch with double drum and double rope mechanism (Double drum for extension ) and (Single drum for tilting )the ladder  one winch is for tilting the ladder from 0 to 90 degree and the another winch is to extend the ladder to required height . Each winch is provided with Ratchet for safety in order to stop the winch reversing back unconditionally.

Load capacity: Over all load capacity of the ladder is 150 kg inclusive of user weight and hand tool

Important: Safe on vertical and Inclined working on ladder – PERMITTED

Guarantee: Our ladders are guaranteed for 12 months from date of Invoice

Additional Information:

• Pay Mode Terms: T/T (Bank Transfer)
• Delivery Time: IMMEDIATE
• Packaging Details: NIL

Approx. Rs 45,000.00 / UnitGet Latest Price

Main frame: This ladder is made up of aluminium alloy “C” section 66*32*3.18 mm thickness. HE30/ 6351 /T6 Grade.

·         Chemical composition (Si- 00.900, Fe- 0.160, Cu- 0.070, Mn-0.60, Mg-0.770, Cr-0.010, Zn-0.010, Ti-0.020, V-0.001, Zr-0.001) Aluminium – 97.50

·         Mechanical properties – UTS(Mpa)-353.14 , % Elongation on 50mm GL- 11, 0.2% Proof stress Mpa – 338.43 (Certificate confirms to IS 733-1983/64430-T6)

Steps: The steps are made up of non slip aluminium alloy corrugated fluted pipe step of 1” dia and 3 mm thickness HE30 / 6063/T6 Grade

·         Chemical composition (Si- 00.500, Fe- 0.140, Cu- 0.002, Mn-0.009, Mg-0.540, Cr-0.002, Zn-0.004, Ti-0.010, V-0.00, Zr-0.00) Aluminium – 98.74

·         Mechanical properties – UTS(Mpa)-182.22, % Elongation on 50mm GL- 14, 0.2% Proof stress Mpa – 173.53 (Certificate confirms to IS 733)

Step Interval: Every step has an interval of 12” for easy climbing and the ladder has a single sliding movement. Both sides of the flutted pipe steps are covered with plastics caps to avoid insects going in.

Platform size: We are providing a platform on top of the ladder(Platform size:17.5×19 inch) which is made up of aluminum alloy framed with aluminum “L” angle and  Chequered sheet of 3 mm thick

MS Trolley: The ladder base is made of MS Channels (100*50*6mm) and the  “L” angle (50*50*6mm). The MS trolley size is 5 feet x 6 feet on ground. The trolley is moved by means of tow bar.

Wheels: We are providing 4 Wheels Solid rubber tyre wheels with double ball bearing of Wheel size 14×4 inch, where 2 fixed wheel at the rear side and 2 round table arrangement at the front side.  This wheel can withstand one tone capacity..

Screw jack: We are  providing 4 Nos Screw Jack for ground resting to immobilizes the ladder when in use. The ladder cannot move if the jacks are screwed to the ground on 4 sides. .

MS Square Block: The ladder can be tilted from 0 to 90 degree by means of special MS Bracket made of square block (125*40mm).The overall tilting load is bared by MS bracket. We are also providing extra tie rod for stability of the ladder in extension position.

Wire rope: We are providing double wire rope for extension and single rope for tilting the ladder. The extension and tilting wire rope is 6 mm thick

Additional Information:

• Item Code: gkm110
• Production Capacity: 100
• Delivery Time: immediate / 2 to 3 weeks
• Packaging Details: nil

Approx. Rs 65,000 / UnitGet Latest Price

Main frame: This ladder is made up of aluminium alloy “C” section 66*32*3.18 mm thickness. HE30/ 6351 /T6 Grade.

·        Chemical composition (Si- 00.900, Fe- 0.160, Cu- 0.070, Mn-0.60, Mg-0.770, Cr-0.010, Zn-0.010, Ti-0.020, V-0.001, Zr-0.001) Aluminium – 97.50

·        Mechanical properties – UTS(Mpa)-353.14 , % Elongation on 50mm GL- 11, 0.2% Proof stress Mpa – 338.43 (Certificate confirms to IS 733-1983/64430-T6)

Steps: The steps are made up of non slip aluminium alloy corrugated fluted pipe step of 1” dia and 3 mm thickness HE30 / 6063/T6 Grade

·        Chemical composition (Si- 00.500, Fe- 0.140, Cu- 0.002, Mn-0.009, Mg-0.540, Cr-0.002, Zn-0.004, Ti-0.010, V-0.00, Zr-0.00) Aluminium – 98.74

·        Mechanical properties – UTS(Mpa)-182.22, % Elongation on 50mm GL- 14, 0.2% Proof stress Mpa – 173.53 (Certificate confirms to IS 733)

Step Interval: Every step has an interval of 12” for easy climbing and the ladder has a single sliding movement. Both sides of the flutted pipe steps are covered with plastics caps to avoid insects going in.

Platform size: We are providing a platform on top of the ladder(Platform size:17.5×19 inch) which is made up of aluminum alloy framed with aluminum “L” angle and  Chequered sheet of 3 mm thick

MS Trolley: The ladder base is made of MS Channels (100*50*6mm) and the  “L” angle (50*50*6mm). The MS trolley size is 5 feet x 6 feet on ground. The trolley is moved by means of tow bar.

Wheels: We are providing 4 Wheels Solid rubber tyre wheels with double ball bearing of Wheel size 14×4 inch, where 2 fixed wheel at the rear side and 2 round table arrangement at the front side.  This wheel can withstand one tone capacity..

Screw jack: We are  providing 4 Nos Screw Jack for ground resting to immobilizes the ladder when in use. The ladder cannot move if the jacks are screwed to the ground on 4 sides. .

MS Square Block: The ladder can be tilted from 0 to 90 degree by means of special MS Bracket made of square block (125*40mm).The overall tilting load is bared by MS bracket. We are also providing extra tie rod for stability of the ladder in extension position.

Wire rope: We are providing double wire rope for extension and single rope for tilting the ladder. The extension and tilting wire rope is 6 mm thick

Winch mechanism: We are specially providing 2 nos winch with double drum and double rope mechanism (Double drum for extension ) and (Single drum for tilting )the ladder  one winch is for tilting the ladder from 0 to 90 degree and the another winch is to extend the ladder to required height . Each winch is provided with Ratchet for safety in order to stop the winch reversing back unconditionally.

Load capacity: Over all load capacity of the ladder is 150 kg inclusive of user weight and hand tool

Approx. Rs 43,000 / UnitGet Latest Price

Main frame: This ladder is made up of aluminium alloy “C” section 66*32*3.18 mm thickness. HE30/ 6351 /T6 Grade.

·         Chemical composition (Si- 00.900, Fe- 0.160, Cu- 0.070, Mn-0.60, Mg-0.770, Cr-0.010, Zn-0.010, Ti-0.020, V-0.001, Zr-0.001) Aluminium – 97.50

·         Mechanical properties – UTS(Mpa)-353.14 , % Elongation on 50mm GL- 11, 0.2% Proof stress Mpa – 338.43 (Certificate confirms to IS 733-1983/64430-T6)

Steps: The steps are made up of non slip aluminium alloy corrugated fluted pipe step of 1” dia and 3 mm thickness HE30 / 6063/T6 Grade

·         Chemical composition (Si- 00.500, Fe- 0.140, Cu- 0.002, Mn-0.009, Mg-0.540, Cr-0.002, Zn-0.004, Ti-0.010, V-0.00, Zr-0.00) Aluminium – 98.74

·         Mechanical properties – UTS(Mpa)-182.22, % Elongation on 50mm GL- 14, 0.2% Proof stress Mpa – 173.53 (Certificate confirms to IS 733)

Step Interval: Every step has an interval of 12” for easy climbing and the ladder has a single sliding movement. Both sides of the flutted pipe steps are covered with plastics caps to avoid insects going in.

Platform size: We are providing a platform on top of the ladder(Platform size:17.5×19 inch) which is made up of aluminum alloy framed with aluminum “L” angle and  Chequered sheet of 3 mm thick

MS Trolley: The ladder base is made of MS Channels (100*50*6mm) and the  “L” angle (50*50*6mm). The MS trolley size is 5 feet x 6 feet on ground. The trolley is moved by means of tow bar.

Wheels: We are providing 4 Wheels Solid rubber tyre wheels with double ball bearing of Wheel size 14×4 inch, where 2 fixed wheel at the rear side and 2 round table arrangement at the front side.  This wheel can withstand one tone capacity..

Screw jack: We are  providing 4 Nos Screw Jack for ground resting to immobilizes the ladder when in use. The ladder cannot move if the jacks are screwed to the ground on 4 sides. .

MS Square Block: The ladder can be tilted from 0 to 90 degree by means of special MS Bracket made of square block (125*40mm).The overall tilting load is bared by MS bracket. We are also providing extra tie rod for stability of the ladder in extension position.

Wire rope: We are providing double wire rope for extension and single rope for tilting the ladder. The extension and tilting wire rope is 6 mm thick

Winch mechanism: We are specially providing 2 nos winch with double drum and double rope mechanism (Double drum for extension ) and (Single drum for tilting )the ladder  one winch is for tilting the ladder from 0 to 90 degree and the another winch is to extend the ladder to required height . Each winch is provided with Ratchet for safety in order to stop the winch reversing back unconditionally.

Load capacity: Over all load capacity of the ladder is 150 kg inclusive of user weight and hand tool

Additional Information:

• Item Code: 110
• Production Capacity: 100
• Delivery Time: immediate / 1 to 2 weeks
• Packaging Details: nil

Approx. Rs 55,000 / PieceGet Latest Price

• This ladder is made up of aluminium alloy “C” section 66x 32x 3.18mm thickness.(Hindalco make HE 30/6063 alloy T6 Grade Aluminium section pressure Grade)
• The steps are made up of anti slip aluminium alloy Industrial corrugated fluted pipe 1”dia, 3 mm thickness.26 OD Size. Every step has a 12” height difference for easy climbing and the ladder has a single sliding movement. Both sides the pipe end covered with plastic caps to avoid insects going in.
• We are providing platform on the top of the ladder (3 feet depth), made up of aluminum alloy chequered sheet OF 16 G. The Chequered sheet is framed with aluminium “L” angle, Size 11/2” x 1”x 1/8” and an extra tool tray.
• The base is made of M.S Channels (100x50x6mm) and the “L” angle (50x50x6mm) and 40x40x6mm. We are providing 4 wheels round table rotated wheels size 14”x4”.( Double Ball bearing type) This wheel can withstand one tone load capacity. we are specially providing 4 Nos maneuverable screw disc for ground resting to immobilize the ladder. The trolley is moved by means of tow-bar.
• The ladder can be tilted from 0 to 90 degree by means of special M.S Bracket made of square block (100x50mm) M.S block is support to axle, size 180x32mm welded to 100x50mm channels. The overall tilting load is beard by M.S bracket to keep the ladder stable and moves smoothly and steadily. We are providing 2 Nos Tie-rod for extra stability of the ladder in extended position. The Steel wire thickness is 6 mm and 6 mm (Double mechanism). The extension of ladder is very easy with smooth run operation by means of winch and wheel mechanism.
• Winch mechanism: We are specially providing 2 winches with double drum and double rope mechanism, one for tilting the ladder from 0 to 90 degree and the other to extend the ladder to required height for easy extension with easy smooth hand operation by means of winch and wheel mechanism

Approx. Rs 45,000 / PieceGet Latest Price

• Closed ht: 10 feet extended ht: 16 feet
• Closed ht: 12 feet extended ht: 20 feet
• Closed ht: 15 feet extended ht: 25 feet
• Closed ht: 17 feet extended ht: 30 feet
• Closed ht: 20 feet extended ht: 36 feet
• Closed ht: 24 feet extended ht: 43 feet
• Closed ht: 20 feet extended ht: 50 feet (Double sliding)
• Closed ht: 24 feet extended ht: 60 feet (Double sliding).

• This ladder is made up of aluminium alloy “C” section 66x 32x 3.18mm thickness.(Hindalco make pressure tested extrusion)
• The steps are made up of anti slip aluminium alloy corrugated fluted pipe 1”dia, 3 mm thickness. Every step has a 12” height difference for easy climbing and the ladder has a single sliding movement. Both sides the pipe end covered with plastic caps to avoid insects going in.
• We are providing projected platform below 3’ from the top of the ladder, made up of aluminum alloy chequered sheet. The chequered sheet framed with aluminium “L” angle, size11/2” x 1”* 1/8” and extra tool tray..
• The base is made of M.S Channels (100x50x6mm) and the “L” angle (50x50x6mm) and 40x40x6mm. We are providing 4 wheels , 2 Nos fixed wheel at the rear side, size 14”x 4” and 2nos swell wheels at the front side, size 14”x4”.(Ball bearing type) This wheel can withstand one tone capacity. In the trolley front side we are specially providing 2 Nos maneuverable screw disc for ground resting to immobilize the ladder. The trolley is moved by means of tow-bar.
• The ladder can be tilted from 0 to 90 degree by means of special M.S Bracket made of square block (100x50mm) M.S block is support to axle, size 180x32mm welded to 100x50mm channels. The overall tilting load is beard by M.S bracket to keep the ladder stable and moves smoothly and steadily. We are providing 2 Nos Tie-rod for extra stability of the ladder in extended position. The wire thickness is 6mm. The extension of ladder is very easy with smooth run operation by means of winch and wheel mechanism.
• Winch mechanism: We are specially providing 2 winches with double drum and double rope mechanism, one for tilting the ladder from 0 to 90 degree and the other to extend the ladder to required height for easy extension with easy smooth hand operation by means of winch and wheel mechanism

Approx. Rs 48,500 / PieceGet Latest Price

Main frame: This ladder is made up of aluminium alloy “C” section 66*32*3.18 mm thickness. HE30/ 6351 /T6 Grade.

teps: The steps are made up of non slip aluminium alloy corrugated fluted pipe step of 1” dia and 3 mm thickness HE30 / 6063/T6 Grade

·        Chemical composition (Si- 00.500, Fe- 0.140, Cu- 0.002, Mn-0.009, Mg-0.540, Cr-0.002, Zn-0.004, Ti-0.010, V-0.00, Zr-0.00) Aluminium – 98.74

·        Mechanical properties – UTS(Mpa)-182.22, % Elongation on 50mm GL- 14, 0.2% Proof stress Mpa – 173.53 (Certificate confirms to IS 733)

Step Interval: Every step has an interval of 12” for easy climbing and the ladder has a single sliding movement. Both sides of the flutted pipe steps are covered with plastics caps to avoid insects going in.

Platform size: We are providing a platform on top of the ladder(Platform size:17.5×19 inch) which is made up of aluminum alloy framed with aluminum “L” angle and  Chequered sheet of 3 mm thick

MS Trolley: The ladder base is made of MS Channels (100*50*6mm) and the  “L” angle (50*50*6mm). The MS trolley size is 5 feet x 6 feet on ground. The trolley is moved by means of tow bar.

Wheels: We are providing 4 Wheels Solid rubber tyre wheels with double ball bearing of Wheel size 14×4 inch, where 2 fixed wheel at the rear side and 2 round table arrangement at the front side.  This wheel can withstand one tone capacity..

Screw jack: We are  providing 4 Nos Screw Jack for ground resting to immobilizes the ladder when in use. The ladder cannot move if the jacks are screwed to the ground on 4 sides. .

MS Square Block: The ladder can be tilted from 0 to 90 degree by means of special MS Bracket made of square block (125*40mm).The overall tilting load is bared by MS bracket. We are also providing extra tie rod for stability of the ladder in extension position.

Wire rope: We are providing double wire rope for extension and single rope for tilting the ladder. The extension and tilting wire rope is 6 mm thick

Winch mechanism: We are specially providing 2 nos winch with double drum and double rope mechanism (Double drum for extension ) and (Single drum for tilting )the ladder  one winch is for tilting the ladder from 0 to 90 degree and the another winch is to extend the ladder to required height . Each winch is provided with Ratchet for safety in order to stop the winch reversing back unconditionally.

Load capacity: Over all load capacity of the ladder is 150 kg inclusive of user weight and hand tool

Important: Safe working – vertical only. Inclined working on ladders – NOT PERMITTED

Guarantee: Our ladders are guaranteed for 12 months from date of Invoice

Approx. Rs 58,000 / PieceGet Latest Price

Aluminium tiltable tower ladder GKM Model no: 119

Additional Information:

• Item Code: 7610
• Production Capacity: 50
• Delivery Time: 2 to 3 weeks
• Packaging Details: no packaging